Reinforced rear blade for tractor DELEKS PRM-H
- Shovel width: 1600 - 2000 mm
- Tractor power: 50 - 90 HP
- Load capacity: 700 kg
- Weight: 191 - 250 kg
Deleks products take about 15 to 20 days. |
DELEKS PRM-H Reinforced Tractor Rear Loader PRM-H
The DELEKS PRM-H reinforced tractor rear shovel is a steel shovel designed for loading and transporting all kinds of materials, such as soil, sand or even snow. It can also be used to dig and level the ground. It is equipped with a manual swing.
This tractor rear loader is suitable for tractors from 50 to 90 HP, its heavy loader has a load capacity of 700 kg, it has a simple and effective tipping mechanism of the loader, thus making it much easier and simpler to use at the time of work.
Its tipping allows unloading in a single movement, and after this the return to the initial position, ready for the next load, its 10 mm thick stainless steel loading blade with cutting edge, allows a good penetration and a long useful life.
The blade is lifted in the middle instead of at the rear, which reduces the stress on the back of the blade and at the hitch level. In this way, there is no need for a high lift to allow materials to fall. This simplifies the work and increases the shovel's longevity.
The arms do not exceed the width of the shovel, which allows for better productivity and avoids close proximity to possible obstacles. There is a safety hinge pin to prevent unintentional dropping of materials.
It is possible to increase the load volume of the shovel from 30 to 50% thanks to the rear door and the upper grid (optional purchase).
Characteristics
Model | PRM-160-H | PRM-200-H |
Total width | 1620.0 mm | 2020.0 mm |
Weight | 191.0 kg | 250.0 kg |
Total height | 935.0 mm | 935.0 mm |
Tractor power | 50 - 90 hp | 60 - 90 hp |
3-point hitch | Cat. 1-2 (ø 19.0-22.0mm / 25.0-28.0mm) | Cat. 1-2 (ø 19.0-22.0mm / 25.0-28.0mm) |
Blade width | 1600.0 mm | 2000.0 mm |
Load capacity | 700.0 kg | |
Loading volume | 0,50 m3 | |
Thickness of the tip plate | 10.0 mm | |
Thickness of shovel plate | 6.0 mm | |
Blade height | 520.0 mm | |
Depth | 800.0 mm | |
Total depth | 1000.0 mm | |
Plate thickness. 3-point hitch | 13.0 mm | |
Distance between lower points | 660.0 - 935.0 mm | |
Inclination | Mechanical | |
Tilt angle | 90° | |
Packing dimensions | 163 x 110 x 107 cm | 203 x 110 x 107 cm |
IMPORTANT NOTICE |
It is mandatory for the customer to check oil and grease levels before start-up. If it is not possible to check the goods at the time of receipt, it must be indicated on the carrier's sheet that the customer is in agreement unless an examination is pending. |
Data sheet
- Working width
- 1600 - 2000 mm
- Tractor power
- 50/60 - 90 HP
- Load capacity
- 700 - 799 Kg
- 3-point hitch for tractor
- Yes
- Country of manufacture
- Italy
- Weight
- 191 - 250 kg
Specific References
- ean13
- 8053470230424
- mpn
- PRM160H
✔️ Advantages of making purchases in the Spanish territory
- National warranty: By purchasing from authorized distributors throughout Spain, you are assured of receiving a 100% Spanish warranty for your products.
- Local after-sales service: In case of any inconvenience or need for after-sales service, you will have a more efficient and accessible support when purchasing within Spain.
❌ Disadvantages of buying outside Spanish territory
- Complicated warranty management: Buying products outside Spain can make warranty management difficult, as there may be problems with the Spanish serial number or delays in the process.
- Limited after-sales service: The availability of after-sales service may be limited or less accessible when purchasing products abroad.
- Tax declaration: When purchasing products outside Spain, customers may be required to make an additional tax declaration, such as an intra-community purchase, which may involve additional tax formalities.
Review
5 other products
Reinforced polidozer for tractor Deleks DDL-250 70-100 HP
- Tractor power 70 - 100 HP
- Blade material: Steel
- Blade height 55cm
- 360º rotation
€1,797.64 VAT incl.
Tractor bucket with hydraulic tipping Geo Italy PRI 180 2H
- Capacity: approximately 850 liters.
- Material thickness: 4 mm
- Rim thickness: 17 mm
- Weight: approximately 300 kg
€1,270.71 VAT incl.
PTO Leveling Blade Deleks DDL-175 40 - 80 HP
- Total width : 1750.0 mm
- Weight : 200.0 kg
- Total height : 1150.0 mm
€988.99 VAT incl.
Leveling blade for Garto tractor CN 130-160 cm
- Weight: 55 kg / 65 kg
- Working width: 1300 mm / 1600 mm
€557.28 VAT incl.
Snow plow for tractor Deleks LN-220-C 50-80HP
- Tractor power: 50 - 80 HP
- Blade width: 2205 mm
- Blade height: 700 mm
- Inclination: 27 degrees
€2,768.21 VAT incl.
Product Reviews / Q&A
-
Reviews (0)
-
Questions & Answers (0)
-
Latest
-
Latest